Specification of WT-JG Dry powder
Item | Test method | Unit | Standard | Actual Measurement |
Shear strength | Normal temperature for 14 days | Mpa | ≥1.0 | 3.88 |
Tensile Strength | Normal temperature for 14 days | Mpa | ≥0.3 | 1.55 |
Water resistance | Normal temperature maintenance 14 days, water 7 days | Mpa | ≥0.7 | 2.75 |
Temperature Resistance | Room temperature curing for 14 days, 100 ℃, 168 hours | Mpa | ≥0.7 | 2.39 |
Frost resistance | Room temperature 15 hours cycle 7 hours | Mpa | ≤0.7 | 2.36 |
linear contraction | % | ＜0.5 | 0.32 |
Usage of WT-JG Dry powder
1, Grass-roots treatment
① If the surface of the concrete oil (refers to the heavier oil) dust must be cleaned.
② summer construction or wall is dry, must be wet before construction.
2, the interface agent mixture
① smear with the interface agent mixture;
According to the area: water = 4: 1 (weight ratio) ratio of mixing to the cream-like, static 15 minutes is to make the material fully soluble, the interface agent will become thicker, this time in a little water, use.
② blistering and brush with the interface agent mixture;
According to the interface agent: water = 3: 1 (mass ratio) ratio of mixing and mixing, static for 15 minutes, stir again, you can use.
3, construction
① smear: the mixture will be even after the interface with mud board smear on the grass, and then pressed the grass board to pull out the grass, can be formed concave and convex, the thickness of about 2mm or so, to be 10-30 minutes (depending on the temperature And different), the cement mortar plastering construction.
Spray: spray gun with a mortar spray gun, the nozzle diameter of 6mm, air pressure 7-8kg / cm spray gun, spray from the wall of the range of 0.5m, sprayed into 1-4mm convex and concave surface.
③ with a brush broom dipped in the interface agent, painted on the concrete surface 1-3mm to form convex and concave surface can be. (Slightly with the spray construction)
④ roof brushing interface agent, the initial coating to be dry, hardened (about 24 hours), before entering the plaster and other operations under the road.
⑤ dosage 1-2kg / m
WT-JG Dry powder deals with the appearance of smooth concrete after stripping, the combination of old and new concrete, aerated concrete, lime sand bricks, and fly ash bricks. To solve these problems due to the surface of the water absorption characteristics or smooth, so that the interface is not easy to cause the plaster layer caused by hollowing, cracking, peeling and other issues.
1. WT-JG Dry powder is powder, each bag weighs 50kg;
2. The water agent of this product is 50kg of liquid;
3. Non-flammable, non-dangerous goods, safe transport, avoiding rain and crashing, damaging the packaging;
4. WT-JG Dry powder is stored in a dry and cool storage, and it is strictly forbidden to contact with water for six months.
Q: Are you factory?
A: We have our own stock factory.
Q: How about your supply ability?
A: We can produce 50tons per day.
Q: How many tons you can load into one 20ft container?
A: Normally we load 25-27tons into one 20ft container. It'll be according to buyer's request.
Q: Can you accept third party inspection?
A: We can accept SGS, BV and other third party inspections.
Q: Where is your main market?
A: We mainly export to Southeast Asia, Africa and Middle east countries.
Q: How about your payment terms?
A: 30% T/T in advance, balance against B/L copy.
